Difference between revisions of "Stations"

From meteoplug
Jump to: navigation, search
 
(95 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
Meteobridge can handle a broad range of weather stations from consumer entry level up to prosumer/professional stations from Davis Instruments, PeetBros or Rainwise.   
+
<languages /><translate>
 +
<!--T:1-->
 +
<br />Meteobridge can handle a broad range of weather stations from consumer entry level up to prosumer/professional stations from Davis Instruments, PeetBros or Rainwise.<br />  
  
−
==Supported Weather Stations==
+
<!--T:2-->
 
{| style="background:none" border="1" cellpadding="5" cellspacing="0"
 
{| style="background:none" border="1" cellpadding="5" cellspacing="0"
 
|+ align="bottom"|''supported weather stations''
 
|+ align="bottom"|''supported weather stations''
Line 8: Line 10:
 
|-
 
|-
 
|<center>[[File:vantage.png]]</center>
 
|<center>[[File:vantage.png]]</center>
−
|'''Davis''' Vantage Pro2, Pro1 (except firmware A)
+
|'''Davis'''<BR>Vantage Pro2, Pro1 (except firmware A)
−
|Vantage Pro including wind, rain, pressure, UV, solar radiation, indoor temperature, outdoor temperature and 7 extra temp/hum sensors are fully supported. Additional "Soil" and "Leaf" sensors as well as pure temperature sensors are also supported. Meteoplug can handle RS232, USB and TCP/IP (WeatherLinkIP) variants of Vantage. Data internally logged in Vantage is checked by Meteoplug when Meteoplug starts operation. If there is historical data not available to Meteoplug so far, this logged data will be transferrred to Meteoplug before logging of live data starts. RS232 Vantage must have set baud rate to 19.200.
+
|Vantage Pro including wind, rain, pressure, UV, solar radiation, indoor temperature, outdoor temperature sensors. In order to connect Vantage with Meteobridge it needs one of the Davis data loggers (serial or USB). If a serial logger is used, it needs to be set to 19.200 baud and a RS232-USB converter based on Prolific pl2303 or FTDI chipset is necessary. Storage capacity of Davis logger is not used at all. Meteobridge allows parallel use of the Vantage by a PC program, which connects to the Meteobridge on port 22222 (like with a Davis IP logger). Meteobridge can also pass through the connection to the Davis station to an additional PC weather program of your liking. Therefore, you can use Meteobridge <u>and</u> a PC weather program in parallel.
 
|-
 
|-
 
|<center>[[File:vue.png]]</center>
 
|<center>[[File:vue.png]]</center>
−
|'''Davis''' Vantage Vue
+
|'''Davis'''<BR>Vantage Vue
−
|Vantage Vue including all available sensors is fully supported. Meteoplug can handle RS232, USB and TCP/IP (WeatherLinkIP) variants of Vantage. Data internally logged in Vantage is handled by Meteoplug as explained for Vantage Pro. RS232 Vantage must have set baud rate to 19.200.  
+
|Vantage Vue including wind, rain, pressure, indoor temperature, outdoor temperature sensors, but without UV or solar sensors. In order to connect Vue with Meteobridge it needs one of the Davis data loggers (serial or USB). If a serial logger is used, it needs to be set to 19.200 baud and a RS232-USB converter based on Prolific pl2303 or FTDI chipset is necessary. Storage capacity of Davis logger is not used at all. Meteobridge allows parallel use of the Vantage by a PC program, which connects to the Meteobridge on port 22222 (like with a Davis IP logger). Meteobridge can also pass through the connection to the Davis station to an additional PC weather program of your liking. Therefore, you can use Meteobridge <u>and</u> a PC weather program in parallel.
 
|-
 
|-
−
|<center>[[File:envoy8x.png]]</center>
+
|<center>[[File:wll.png]]</center>
−
|'''Davis''' Envoy8x
+
|'''Davis'''<BR>WeatherLink Live
−
|New Envoy8x receiving unit from Davis is supported. Connection to Meteoplug client is done via RS232 or USB data logger from Davis. Historical data stored in the receiving unit are not considered at the moment. Initial configuration of Envoy8x regarding connected weather stations has to be done upfront with the PC programs provided by Davis. Meteoplug client is not capable to do this.  
+
|WeatherLink Live can gather data from up to 8 Davis sensor arrays and does send data to the proprietary, subscription-based weather network "Davis WeatherLink". Apart from that the WeatherLink Live does also provide weather data in the LAN when requested. Meteobridge is able to read data from the unit and to make use of data from all connected sensor arrays. In order to connect to the WeatherLink Live Meteobridge needs to know the IP of the unit.
 +
|-
 +
|<center>[[File:meteostick.png]]</center>
 +
|'''smartbedded''' Meteostick<BR><BR><small>for RF reception of Davis and Fine Offset sensor arrays</small>
 +
|Meteostick reads RF signals from Davis Vue and Vantage Pro 2 sensors (US, EU and AU models) directly and makes data accessible without need of a Davis Console/Envoy and Logger. Indoor humidity is not provided, indoor temp is not reported accurately, because the sensor in the USB stick sized device heats up a bit during operation. When used with Meteobridge FW 1.4 or newer, no USB hub is needed. Use of a USB cradle is recommended to bring some distance between the RF noise emitting Meteobridge and the Meteostick. Since Meteostick firmware 2.2 data from Davis repeaters is also supported. Since Meteostick firmware 2.0 also data from outdoor sensor array (WH24) of Fine Offset HP-100x (aka Ambientweather Observer WS-100x) can be received (US and EU models). You find more details about Meteostick [http://www.smartbedded.com/wiki/index.php/Meteostick here]. Remark: Meteobridge does not offer pass through options for Meteostick as with the Davis loggers.
 
|-
 
|-
 
|<center>[[File:wmr928.png]]</center>
 
|<center>[[File:wmr928.png]]</center>
−
|'''Oregon''' WMR928 (EU), WMR968 (US)
+
|'''Oregon'''<BR>WMR968 (US), WMR928 (EU)
−
|This model has a RS232 connector that needs a RS232-to-USB converter (based on CP2101, FTDI or PL2303 chipset). Serial protocol of this weather station is well understood and widely documented. As a result Meteoplug does support all of it's features. Disadvantage of the station not to have a data logger included is compensated by Meteoplug. Station is limited in terms of sensor variety. It can handle a maximum of 3 additional thermo/hygro sensors and is lacking support of an UV sensor.
+
|This model has a RS232 connector that needs a RS232-USB converter (based on FTDI or Prolific pl2303 chipset). Station does not provide UV or solar sensors.
 +
|-
 +
|<center>[[File:wmr100.png]]</center>
 +
|'''Oregon'''<BR>WMR100, WMR88
 +
|This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). An optional UV sensor is supported as well.
 +
|-
 +
|<center>[[File:wmr89.png]]</center>
 +
|'''Oregon'''<BR>WMR89, WMR89A
 +
|This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). An optional UV sensor is supported as well.
 
|-
 
|-
 
|<center>[[File:wmr200.png]]</center>
 
|<center>[[File:wmr200.png]]</center>
−
|'''Oregon''' WMR200
+
|'''Oregon'''<BR>WMR200
−
|This model has a USB connector that can directly connected to the Meteoplug client. Internal Datalogger of WMR200 will not be used by Meteoplug. WMR200 has problems in reporting actual sensor readings, when data logger is completely filled. It is recommended to set the data logging interval to the maximum (longest duration). This takes care that the data logger will not reach its capacity for months. However, you should take care to empty the data logger's buffer from time to time manually at the WMR 200 base station. All sensors for WMR200 are supported, including additional thermo/hygro sensors as well as an UV sensor.
+
|This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). Internal datalogger of WMR200 will not be used by Meteobridge. WMR200 has problems in reporting actual sensor readings, when data logger is completely filled. It is recommended to set the data logging interval to the maximum (longest duration). This takes care that the data logger will not reach its capacity for months. However, you should take care to empty the data logger's buffer from time to time manually at the WMR200 base station. Beside the standard sensors it can also support UV sensors.
 
|-
 
|-
−
|<center>[[File:wmr100.png]]</center>
+
|<center>[[File:wmr300w78.png]]</center>
−
|'''Oregon''' WMR100
+
|'''Oregon'''<BR>WMR300
−
|This model has a USB connector that can directly connected to the Meteoplug client. Meteoplug supports all available sensors for WMR100, including additional thermo/hygro sensors as well as an UV sensor
+
|This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). Internal datalogger of WMR300 will not be used by Meteobridge.
 
|-
 
|-
 
|<center>[[File:wmrs200.png]]</center>
 
|<center>[[File:wmrs200.png]]</center>
−
|'''Oregon''' WMRS200
+
|'''Oregon'''<BR>WMRS200
−
|This station is like a WMR100 with sensors from WMR200 but without any display. WMRS200 is powered from Meteoplug via USB connector. All sensors applicable to WMRS200 are supported by Meteoplug.
+
|This station is like a WMR100 with sensors from WMR200 but without any display. WMRS200 is connected to Meteobidge USB port (as WMR200) and is also powered by the USB connector.
−
|-
+
−
|<center>[[File:rms300.png]]</center>
+
−
|'''Oregon''' RMS300
+
−
|This station gets directly connected by an USB cable and is just capable to report data from a maximum of 3 temp/hygro sensors. Out-door sensor is included in the package (THGN-132N) and mapped to channel 0 by Meteoplug. Sensors for wind, rain, UV, pressure are not supported. Additional temp/hygro sensors have to be of type THGR810. temp/hygro sensor included in the console is reported on channel 9.
+
 
|-
 
|-
 
|<center>[[File:te923.png]]</center>
 
|<center>[[File:te923.png]]</center>
−
|'''Hideki''' TE923
+
|'''Meade'''<BR>TE923, TE827, TE821, DV928, W831
−
|TE923 weather station from Hideki is connected via USB and is sold with various brand names (Mebus, Irox, Honeywell, Nexus). TE923 had various hardware revisions over time. Meteoplug supports hardware versions 3, and 4. Very old version 1, that does not provide live weather data on the USB port, and version 2 are not supported.
+
|These weather stations are connected via USB and are sold with various brand names (Mebus, Irox, Honeywell, Nexus, Ventus). Meteobridge supports recent hardware versions which provide live weather data on the USB port. Internal data logger functionality of TE923 is not used by Meteobridge. Station is connected via USB (with a USB 2.0 hub inbetween).
−
Meteoplug just makes use of the live data of TE923, internal data logger functionality of TE923 is not used by Meteoplug.  
+
|-
 +
|<center>[[File:ws1640.png]]</center>
 +
|'''LaCrosse'''<BR>WS1640
 +
|This weather stations is connected via USB and is from an USB point of view identical to the ones above from Meade, Mebus, Irox, etc. Meteobridge supports recent hardware versions which provide live weather data on the USB port. Internal data logger functionality is not used by Meteobridge. Station is connected via USB (with a USB 2.0 hub inbetween).
 
|-
 
|-
 
|<center>[[File:wh1080.png]]</center>
 
|<center>[[File:wh1080.png]]</center>
−
|'''Fine Offset Electronics''' WH1080, WH1081
+
|'''Ambient Weather '''<BR>WS1090, WS2080
−
|WH1080 weather station from Fine Offset Electronics is also branded as Watson W-8681, WX-2008, National Geographic 265 NE, Elecsa 6975/ 6976, Ambient Weather WS-1080/WS-2080. Meteoplug just makes use of live data of the WH-1080, internal data logger functionality of the WH1080 is not used by Meteoplug. Weather forecast icon is not supported as well.  
+
|These weather stations manufactured by Fine Offset Electronics (WH1080, WH2080, WH3080) are also branded as Watson W-8681, WX-2008, National Geographic 265 NE, Elecsa 6975/ 6976, etc. Meteobridge makes use of live data, internal data logger functionality is not used. Stations can be connected via USB. UV sensors is used if present.
 +
|-
 +
|<center>[[File:wh2310.png]]</center>
 +
|'''Fine Offset '''<BR>WH4000, WH2310
 +
|These weather stations also rebranded as Tycon TP2700 are manufactured by Fine Offset Electronics and use a bit different protocol compared to the WH1080 and alike clones. Meteobridge makes use of live data, internal data logger functionality is not used. Stations can be connected via USB. UV/Solar sensor is used if present.
 +
|-
 +
|<center>[[File:gw1000x72.png]]</center>
 +
|'''Fine Offset'''<BR>GW1000
 +
|This weather data gateway collects data from a couple of Fine Offset sensors and sensor arrays and is able to provide this data in the LAN. Meteobridge can read data from the GW1000 and supports all connected sensors. In order to connect to the GW1000 Meteobridge needs to know the IP of the GW1000. The GW1000 is also branded Froggit DP1500.
 +
 
 +
|-
 +
|<center>[[File:oserverip.png]]</center>
 +
|'''Ambient Weather '''<BR>Observer IP
 +
|This LAN device uploads data from the Weather Observer line of weather sensors to Weather Underground. Meteobridge can also make use of the Oberserver IP.  
 
|-
 
|-
 
|<center>[[File:ultimeter.png]]</center>
 
|<center>[[File:ultimeter.png]]</center>
−
|'''Peet Bros''' Ultimeter 100, 800, 2100
+
|'''Peet Bros'''<BR>Ultimeter 100, 800, 2100
−
| Ultimeter weather stations from Peet Bros are supported. Wind, rain, pressure, indoor and outdoor temperature and humidity are used. Supported Peet Bros data protocols are "data logging", "packet", "complete record".
+
| Ultimeter weather stations from Peet Bros are supported. Wind, rain, pressure, indoor and outdoor temperature and humidity are used. Station needs to be set to "data logging", "packet" or "complete record (preferred) mode with 2400 baud transfer rate. Station needs a RS232-USB converter based on Prolific pl2303 or FTDI chipset.
 
|-
 
|-
 
|<center>[[File:mk3.png]]</center>
 
|<center>[[File:mk3.png]]</center>
−
|'''RainWise''' MkIII
+
|'''Rainwise'''<BR>MkIII
−
|MkIII weather station from RainWise is supported including wind, rain, pressure, outdoor temperature and humidity. Meteoplug uses classical CRC communication type. Sensor thb0 reports pressure and outdoor temp/hum. Sensor th0 also reports outdoor temp/hum.
+
|MkIII weather station from Rainwise is supported including wind, rain, pressure, outdoor temperature and humidity. Meteobridge can handle the old (white box) serial MKIIICC computer interface (with a RS232-USB converter based on pl2303 or FTDI) and the new (black box) CC-3000 computer interface.
 +
|-
 +
|<center>[[File:ws600.png]]</center>
 +
|'''Lufft'''<BR>WS600/601/700/500/200
 +
|WS600 and alike weather stations from Lufft are supported, when attached as USB serial device by a specific UMB component. Station needs to be configured on channel 1. Data provided is wind speed, wind direction, temperature, humidity, pressure, rain rate, rain total, solar radiation, uv index. Precipitation type is not evaluated by Meteobridge.
 +
|-
 +
|<center>[[File:ventus.png]]</center>
 +
|'''Lufft'''<BR>Ventus V200A
 +
|V200A is a station from Lufft that focuses on wind and temperature. It is supported by Meteobridge when attached as USB serial device by a specific UMB component. Station needs to be configured on channel 1. Data provided is wind speed, wind direction, temperature and pressure.
 +
|-
 +
|<center>[[File:thies.png]]</center>
 +
|'''Thies'''<BR>Clima Sensor US
 +
|Clima Sensor US is supported. It needs to be connected via a RS-485/422 to USB converter to the Meteobridge.
 +
|-
 +
|<center>[[File:acurite.png]]</center>
 +
|'''Acurite'''<BR>1025/1035/1525
 +
|USB enabled weather stations from Acurite are supported including wind, rain, pressure, outdoor and indoor temperature and humidity. Meteobridge directly connects to the USB interface of the Acurite console. Important: Acurite console has to be switched to USB mode 3. Warning: Inside humidity is not reported correctly.
 
|-
 
|-
 
|<center>[[File:ws2300.png]]</center>
 
|<center>[[File:ws2300.png]]</center>
−
|'''La Crosse''' WS2300
+
|'''LaCrosse'''<BR>WS2300
−
|WS2300 weather station is supported. Data is received by a plug-in available under GPL. Source code can be at download from download section of "meteohub.de".
+
|WS2300 weather station is supported. Warning: WS2300 can deliver sporadic false weather data readings caused by interface problems. WS2300 needs a RS232-USB converter witch pl2303 or FTDI chipset.  
 
|-
 
|-
 
|<center>[[File:ws300.png]]</center>
 
|<center>[[File:ws300.png]]</center>
−
|'''ELV''' WS300PC/444/500 and various clones (WS550/777/888)
+
|'''LaCrosse / ELV'''<BR>WS300PC/444/500 and various clones (WS550/777/888, WDC7000)
 
|WS300 weather station and clones are supported and connected via USB.
 
|WS300 weather station and clones are supported and connected via USB.
−
|}
 
−
 
−
=== Supported Data Acquisition Devices ===
 
−
{| style="background:none" border="1" cellpadding="5" cellspacing="0"
 
−
|+ align="bottom"|''supported data ackquisition devices''
 
−
!colspan="2"|Device
 
−
! Description
 
 
|-
 
|-
−
|<center>[[File:rfxcom.png]]</center>
+
|<center>[[File:wflow.png]]</center>
−
| '''RFXCOM''' 433MHz-Receiver for Oregon Scientific sensors (USB/LAN/WLAN)
+
|'''WeatherFlow'''<BR>AIR and SKY
−
| RFXCOM Receiver in 433MHz band can read all kinds of Oregon Scientific sensors and RFXmeter sensors, which can do monitoring of energy consumption. Receivers are available with USB connection (80002), LAN connection (81003), WLAN (82003)
+
|AIR and SKY stations are supported. Meteobridge connects to the HUB delivered with the AIR/SKY units and reads out data via the local LAN/WLAN.
 
|-
 
|-
−
|<center>[[File:rfxtrx.png]]</center>
+
|<center>[[File:w835.png]]</center>
−
| '''RFXtrx433 USB''' 433MHz-Transceiver for a broad range of sensors
+
|'''Ventus'''<BR>W835
−
| RFXtrx433 USB is the follow-on product of older RFXCOM above and can handle a lot of RF sensors in 433MHz band. Supported sensors are the ones from Oregon Scientific, TFE and other companies. RFXtrx connects via USB to Meteoplug client.
+
|W835 weather station is supported and connected via USB.
−
|-
+
−
|<center>[[File:em1010PC.png]]</center>
+
−
| '''ELV, Conrad''' Energy monitors EM1010PC and EM1000
+
−
| Meteoplug can read data from these USB connected energy monitoring devices. Information provided is actual power demand and total energy consumption.
+
−
|-
+
−
|<center>[[File:envi.png]]</center>
+
−
| '''Current Cost''' Energy monitor Envi CC128
+
−
| Meteoplug can read data from this USB connected energy monitoring device. Information provided is indoor temperature and actual power demand.  
+
 
|-
 
|-
 +
|<center>[[File:rs500.png]]</center>
 +
|'''ELV'''<BR>RS500 Climate Logger
 +
|RS500 room climate logger is supported and connected via USB.
 
|}
 
|}
 +
 +
<!--T:3-->
 +
Remark: All stations connected via USB will need a small cheap USB 2.0 hub to be connected to Meteobridge, when TP-Link platform (MR3020, MR3040, WR703N) or D-Link (DIR-505) is used. Reason is a limitation in Atheros chipset in these platforms. Any passive USB 2.0 router for a few Euros/Dollars should do. When ASUS WL-330N3G is used as platform, no USB hub is needed.
 +
 +
<!--T:4-->
 +
Not supported stations are LaCrosse 3600, 2800, 2500, 2000, Acurite Access.
 +
</translate>

Latest revision as of 21:40, 26 November 2019

Other languages:
Deutsch • ‎English

Meteobridge can handle a broad range of weather stations from consumer entry level up to prosumer/professional stations from Davis Instruments, PeetBros or Rainwise.
supported weather stations
Weather station Description
Vantage.png
 Davis
Vantage Pro2, Pro1 (except firmware A) 		Vantage Pro including wind, rain, pressure, UV, solar radiation, indoor temperature, outdoor temperature sensors. In order to connect Vantage with Meteobridge it needs one of the Davis data loggers (serial or USB). If a serial logger is used, it needs to be set to 19.200 baud and a RS232-USB converter based on Prolific pl2303 or FTDI chipset is necessary. Storage capacity of Davis logger is not used at all. Meteobridge allows parallel use of the Vantage by a PC program, which connects to the Meteobridge on port 22222 (like with a Davis IP logger). Meteobridge can also pass through the connection to the Davis station to an additional PC weather program of your liking. Therefore, you can use Meteobridge and a PC weather program in parallel.
Vue.png
 Davis
Vantage Vue 		Vantage Vue including wind, rain, pressure, indoor temperature, outdoor temperature sensors, but without UV or solar sensors. In order to connect Vue with Meteobridge it needs one of the Davis data loggers (serial or USB). If a serial logger is used, it needs to be set to 19.200 baud and a RS232-USB converter based on Prolific pl2303 or FTDI chipset is necessary. Storage capacity of Davis logger is not used at all. Meteobridge allows parallel use of the Vantage by a PC program, which connects to the Meteobridge on port 22222 (like with a Davis IP logger). Meteobridge can also pass through the connection to the Davis station to an additional PC weather program of your liking. Therefore, you can use Meteobridge and a PC weather program in parallel.
Wll.png
 Davis
WeatherLink Live 		WeatherLink Live can gather data from up to 8 Davis sensor arrays and does send data to the proprietary, subscription-based weather network "Davis WeatherLink". Apart from that the WeatherLink Live does also provide weather data in the LAN when requested. Meteobridge is able to read data from the unit and to make use of data from all connected sensor arrays. In order to connect to the WeatherLink Live Meteobridge needs to know the IP of the unit.
Meteostick.png
 smartbedded Meteostick

for RF reception of Davis and Fine Offset sensor arrays 		Meteostick reads RF signals from Davis Vue and Vantage Pro 2 sensors (US, EU and AU models) directly and makes data accessible without need of a Davis Console/Envoy and Logger. Indoor humidity is not provided, indoor temp is not reported accurately, because the sensor in the USB stick sized device heats up a bit during operation. When used with Meteobridge FW 1.4 or newer, no USB hub is needed. Use of a USB cradle is recommended to bring some distance between the RF noise emitting Meteobridge and the Meteostick. Since Meteostick firmware 2.2 data from Davis repeaters is also supported. Since Meteostick firmware 2.0 also data from outdoor sensor array (WH24) of Fine Offset HP-100x (aka Ambientweather Observer WS-100x) can be received (US and EU models). You find more details about Meteostick here. Remark: Meteobridge does not offer pass through options for Meteostick as with the Davis loggers.
Wmr928.png
 Oregon
WMR968 (US), WMR928 (EU) 		This model has a RS232 connector that needs a RS232-USB converter (based on FTDI or Prolific pl2303 chipset). Station does not provide UV or solar sensors.
Wmr100.png
 Oregon
WMR100, WMR88 		This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). An optional UV sensor is supported as well.
Wmr89.png
 Oregon
WMR89, WMR89A 		This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). An optional UV sensor is supported as well.
Wmr200.png
 Oregon
WMR200 		This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). Internal datalogger of WMR200 will not be used by Meteobridge. WMR200 has problems in reporting actual sensor readings, when data logger is completely filled. It is recommended to set the data logging interval to the maximum (longest duration). This takes care that the data logger will not reach its capacity for months. However, you should take care to empty the data logger's buffer from time to time manually at the WMR200 base station. Beside the standard sensors it can also support UV sensors.
Wmr300w78.png
 Oregon
WMR300 		This model has a USB connector that can be connected to the Meteobridge client (with a USB 2.0 hub inbetween). Internal datalogger of WMR300 will not be used by Meteobridge.
Wmrs200.png
 Oregon
WMRS200 		This station is like a WMR100 with sensors from WMR200 but without any display. WMRS200 is connected to Meteobidge USB port (as WMR200) and is also powered by the USB connector.
Te923.png
 Meade
TE923, TE827, TE821, DV928, W831 		These weather stations are connected via USB and are sold with various brand names (Mebus, Irox, Honeywell, Nexus, Ventus). Meteobridge supports recent hardware versions which provide live weather data on the USB port. Internal data logger functionality of TE923 is not used by Meteobridge. Station is connected via USB (with a USB 2.0 hub inbetween).
Ws1640.png
 LaCrosse
WS1640 		This weather stations is connected via USB and is from an USB point of view identical to the ones above from Meade, Mebus, Irox, etc. Meteobridge supports recent hardware versions which provide live weather data on the USB port. Internal data logger functionality is not used by Meteobridge. Station is connected via USB (with a USB 2.0 hub inbetween).
Wh1080.png
 Ambient Weather
WS1090, WS2080 		These weather stations manufactured by Fine Offset Electronics (WH1080, WH2080, WH3080) are also branded as Watson W-8681, WX-2008, National Geographic 265 NE, Elecsa 6975/ 6976, etc. Meteobridge makes use of live data, internal data logger functionality is not used. Stations can be connected via USB. UV sensors is used if present.
Wh2310.png
 Fine Offset
WH4000, WH2310 		These weather stations also rebranded as Tycon TP2700 are manufactured by Fine Offset Electronics and use a bit different protocol compared to the WH1080 and alike clones. Meteobridge makes use of live data, internal data logger functionality is not used. Stations can be connected via USB. UV/Solar sensor is used if present.
Gw1000x72.png
 Fine Offset
GW1000 		This weather data gateway collects data from a couple of Fine Offset sensors and sensor arrays and is able to provide this data in the LAN. Meteobridge can read data from the GW1000 and supports all connected sensors. In order to connect to the GW1000 Meteobridge needs to know the IP of the GW1000. The GW1000 is also branded Froggit DP1500.
Oserverip.png
 Ambient Weather
Observer IP 		This LAN device uploads data from the Weather Observer line of weather sensors to Weather Underground. Meteobridge can also make use of the Oberserver IP.
Ultimeter.png
 Peet Bros
Ultimeter 100, 800, 2100 		Ultimeter weather stations from Peet Bros are supported. Wind, rain, pressure, indoor and outdoor temperature and humidity are used. Station needs to be set to "data logging", "packet" or "complete record (preferred) mode with 2400 baud transfer rate. Station needs a RS232-USB converter based on Prolific pl2303 or FTDI chipset.
Mk3.png
 Rainwise
MkIII 		MkIII weather station from Rainwise is supported including wind, rain, pressure, outdoor temperature and humidity. Meteobridge can handle the old (white box) serial MKIIICC computer interface (with a RS232-USB converter based on pl2303 or FTDI) and the new (black box) CC-3000 computer interface.
Ws600.png
 Lufft
WS600/601/700/500/200 		WS600 and alike weather stations from Lufft are supported, when attached as USB serial device by a specific UMB component. Station needs to be configured on channel 1. Data provided is wind speed, wind direction, temperature, humidity, pressure, rain rate, rain total, solar radiation, uv index. Precipitation type is not evaluated by Meteobridge.
Ventus.png
 Lufft
Ventus V200A 		V200A is a station from Lufft that focuses on wind and temperature. It is supported by Meteobridge when attached as USB serial device by a specific UMB component. Station needs to be configured on channel 1. Data provided is wind speed, wind direction, temperature and pressure.
Thies.png
 Thies
Clima Sensor US 		Clima Sensor US is supported. It needs to be connected via a RS-485/422 to USB converter to the Meteobridge.
Acurite.png
 Acurite
1025/1035/1525 		USB enabled weather stations from Acurite are supported including wind, rain, pressure, outdoor and indoor temperature and humidity. Meteobridge directly connects to the USB interface of the Acurite console. Important: Acurite console has to be switched to USB mode 3. Warning: Inside humidity is not reported correctly.
Ws2300.png
 LaCrosse
WS2300 		WS2300 weather station is supported. Warning: WS2300 can deliver sporadic false weather data readings caused by interface problems. WS2300 needs a RS232-USB converter witch pl2303 or FTDI chipset.
Ws300.png
 LaCrosse / ELV
WS300PC/444/500 and various clones (WS550/777/888, WDC7000) 		WS300 weather station and clones are supported and connected via USB.
Wflow.png
 WeatherFlow
AIR and SKY 		AIR and SKY stations are supported. Meteobridge connects to the HUB delivered with the AIR/SKY units and reads out data via the local LAN/WLAN.
W835.png
 Ventus
W835 		W835 weather station is supported and connected via USB.
Rs500.png
 ELV
RS500 Climate Logger 		RS500 room climate logger is supported and connected via USB.

Remark: All stations connected via USB will need a small cheap USB 2.0 hub to be connected to Meteobridge, when TP-Link platform (MR3020, MR3040, WR703N) or D-Link (DIR-505) is used. Reason is a limitation in Atheros chipset in these platforms. Any passive USB 2.0 router for a few Euros/Dollars should do. When ASUS WL-330N3G is used as platform, no USB hub is needed.

Not supported stations are LaCrosse 3600, 2800, 2500, 2000, Acurite Access.

Retrieved from "https://wiki.meteoplug.com/wiki/index.php?title=Stations&oldid=7925"